Sikadur®-732

A solvent-free, thixotropic 2-component structural epoxy resin adhesive. Provides a high-strength bond between new and old concrete, steel, masonry, and wood. Highly effective on dry surfaces with high early and final strength. Suitable for grouting bolts, dowels, and pins.

Overview

Specifications

Technical Information

Usage

• Bonding fresh, plastic concrete to hardened concrete and steel
• Grouting bolts, dowels, and pins
• Structural adhesive for concrete, masonry, metal, and wood

Advantages

• High strength bonding and adhesion
• Excellent adhesion to most structural materials
• High early and final strength
• Highly effective on dry surfaces
• Solvent-free

Packaging

• 5 kg set (Component A + Component B)

Colour

• Concrete grey

Product Details

Product Information

Application

Application Information

Application Steps

• Substrate Preparation: Surface must be clean and sound. May be dry or damp but free of standing water. Remove dust, laitance, grease, curing compounds, impregnations, waxes, foreign particles, and disintegrated materials. Concrete: sandblast or use other approved mechanical methods. Steel: sandblast to white metal finish (SA 2½).
• Mixing: Pre-mix each component separately. Proportion 2 parts Component A to 1 part Component B into a clean pail. Mix thoroughly for 3 minutes with a paddle on low-speed drill (400–600 rpm) until uniform in colour. Mix only the quantity that can be used within the pot life.
• Application: Apply Sikadur®-732 evenly onto the prepared substrate at 0.3–0.8 kg/m² using a brush, roller, or trowel. Place fresh concrete or structural element onto the adhesive while it is still wet and tacky. For bolt/dowel grouting, inject or pour into the hole and insert the bolt immediately.
• Important Notes: Do not exceed the pot life. Do not add solvents or thinners. Protect from rain and moisture until fully cured.

Sika AnchorFix®-2+ Tropical

A solvent and styrene-free, 2-component epoxy acrylate anchoring adhesive designed for medium to high load applications in hot and tropical climatic conditions. Fast curing, non-sag even overhead, and compatible with standard dispensing guns.

Overview

Specifications

Usage

• Chemical anchoring in solid concrete and masonry
• Anchoring of threaded rods and reinforcement bars
• Medium to high load structural fixings
• Suitable for hot and tropical climatic conditions

Advantages

• Fast curing – ready for loading in as little as 40 minutes at +35°C to +40°C
• Solvent and styrene free
• Non-sag – suitable for vertical and overhead applications
• Compatible with standard dispensing guns
• Medium to high load capacity
• Formulated for tropical and high-temperature environments

Packaging

• 300 ml / 490 g cartridge (A+B)

Colour

• Grey (mixed)

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Consumption depends on anchor diameter, embedment depth, and substrate type. Refer to Sika Technical Documentation Ref: 870 43 07 for design details.
• Pump approximately twice until both components come out uniformly before starting application.

Application Steps

• Cartridge Preparation (300 ml, 550 ml, 850 ml): Unscrew cap → Cut film → Screw on static mixer → Place in dispenser and start application.
• Cartridge Preparation (350 ml, 825 ml): Unscrew cap → Remove cap → Screw on static mixer → Place in dispenser and start application.
• Substrate Quality: Concrete and mortar must be older than 28 days. Verify substrate strength; perform pull-out tests if unknown.
• Hole Preparation: Drill hole to required diameter and depth. Clean hole with blow pump or oil-free compressed air from the bottom (min. 2x). Brush with special steel brush (min. 2x, brush diameter larger than hole). Repeat blow cleaning (min. 2x). Hole must be clean, dry, and free from oil and grease. Clean threaded rods and reinforcement bars thoroughly.
• Priming: Pump adhesive twice until both parts come out uniformly. Release gun pressure and clean cartridge opening with a cloth.
• Injection: Inject adhesive from the bottom of the hole while slowly drawing back the static mixer. Avoid entrapping air. Use extension tubing for deep holes.
• Anchor Insertion: Insert anchor with a rotary motion into the filled hole within the open time. Some adhesive must come out of the hole. Do not move or load the anchor during curing time.
• Cleaning: Clean all tools immediately with Sika® Colma Cleaner. Wash hands with warm soap water. Hardened material can only be removed mechanically.

SikaGrout®-214 KH

A pumpable, dual shrinkage-compensated, self-levelling, prebagged cementitious grout with extended working time. Suitable for machine foundations, structural repairs, and grouting works with clearances as low as 5 mm. Approved for compatibility with drinking water (PSB report 57S030976-SLE-2).

Overview

Specifications

Usage

• Machine foundations and base plate grouting
• Columns in precast construction
• Concrete anchors and anchor bolt grouting
• Bridge bearings
• Cavities, gaps, recesses, and rail beds
• Honeycombs (pre-packed grouting)
• Suitable for clearances as low as 5 mm

Advantages

• Easy to mix and apply with good flow characteristics
• Rapid strength development and high ultimate strengths
• Dual shrinkage compensation (gaseous expansion in plastic stage + crystalline expansion in hardened stage)
• Impact resistant, non-corrosive, non-toxic, and chloride free
• Extended working time and good pumping properties
• Approved for compatibility with drinking water

Packaging

• 25 kg / bag

Colour

• Grey powder

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Flowable: 1.84 kg per litre of mortar – 74 bags per m³
• Pourable: 1.90 kg per litre of mortar – 76 bags per m³
• For sections thicker than 50 mm, extend with graded 10 mm silt-free aggregates (max. 1:1 by weight)

Application Steps

• Mixing: Pour 70–80% of premeasured water into a clean container. Gradually add the full bag while continuously mixing. Add remaining water and mix for 2–3 minutes at ~500 rpm (slow speed drill and paddle). For large quantities, use a forced-action mixer. Do not use free-fall mixers.
• Application: After mixing, stir lightly with a spatula to release entrapped air, then pour immediately into prepared formwork. Maintain sufficient pressure head for uninterrupted flow. For large areas, maintain continuous flow and use heavy-duty diaphragm, screw feed, or piston pumps as needed.
• Specific Uses: Base plate grouting (pourable), formwork/honeycomb repair (flowable/pourable), anchor bolt grouting (stiff), large volume grouting >50 mm (extend with 10 mm aggregates, max 1:1 by weight).
• Curing: If formwork repair, leave formwork in place for at least 3 days. Upon removal, cure exposed surfaces immediately with Antisol®-E curing compound or approved equivalent.
• Cleaning: Clean all tools and equipment with water immediately after use. Hardened material can only be removed mechanically.

Sikadur®-31 CF Normal

A moisture-tolerant, thixotropic, structural 2-component epoxy adhesive and repair mortar for use at +10°C to +30°C. CE-marked per EN 1504-4 for structural bonding. No primer required.

Overview

Specifications

Usage

• Structural adhesive for concrete, natural stone, ceramics, fiber cement, mortar, bricks, masonry, steel, iron, aluminium, wood, polyester, epoxy, and glass
• Repair mortar for corners, edges, holes, and void filling
• Vertical and overhead applications
• Joint and crack filling, arris/edge repair

Advantages

• Easy to mix and apply
• Very good adhesion to most construction materials
• High initial and ultimate mechanical strength
• Thixotropic – non-sag on vertical and overhead surfaces
• Hardens without shrinkage
• No primer needed
• Different coloured components for mixing control
• Good abrasion and chemical resistance
• Impermeable to liquids and water vapour

Packaging

• 1.2 kg (A+B) pre-batched unit – box of 6 x 1.2 kg
• 6 kg (A+B) pre-batched unit – pallets of 480 kg (80 x 6 kg)

Colour

• Component A: White
• Component B: Dark grey
• Mixed: Concrete grey

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• ~1.9 kg/m² per mm of thickness

Application Steps

• Substrate Quality: Concrete and mortar must be older than 28 days. Surface must be clean, dry or mat damp (no standing water), and free from oil, grease, coatings, and loose particles. Steel must be de-rusted to Sa 2.5 standard.
• Substrate Preparation: Concrete/mortar/stone/bricks: remove laitance and contaminants to achieve an open-textured surface. Steel: blast clean and vacuum; avoid dew point conditions.
• Mixing: Mix components A+B for at least 3 minutes with a mixing spindle at max. 300 rpm until smooth and uniform grey. Pour into a clean container and stir for 1 more minute at low speed to minimise air entrapment. Mix only the quantity usable within pot life.
• Application: Apply directly to the prepared substrate. For vertical surfaces, product is non-sag up to 15 mm. Do not mix the next unit until the previous one is fully used. To extend workability at high temperatures, divide mixed adhesive into smaller portions or pre-chill components (not below +5°C).
• Cleaning: Clean all tools immediately after use with Sika® Colma Cleaner. Hardened material can only be removed mechanically.

SikaCeram®-188 KH

A high performance, thin layer cementitious tile adhesive (C2TE) for bonding ceramic, porcelain, and mosaic tiles on floors and walls. Suitable for interior and exterior use with excellent slip resistance and extended open time.

Overview

Specifications

Usage

• Ceramic, porcelain, and homogeneous tiles
• All types of low and high absorption tiles
• Mosaics of every type
• Large format tiles and under-floor heating systems
• Tile-on-tile refurbishment (walls and floors)
• Interior painted walls (if paint coating is well bonded and sound)
• Substrates: concrete, mortar, bricks, tiled surfaces
• Interior and exterior, walls and floors

Advantages

• Easy to use with excellent workability and thixotropic consistency
• No sagging or tile slip on vertical surfaces, even with heavy tiles
• Very good adhesion to most common substrates and existing tiles
• Extended open time and adjustability
• Tile-on-tile refurbishment system compatible
• Compatible with Sikalastic®-1K, SikaTop® Seal-107, and SikaTop® Seal-109

Packaging

• 20 kg / bag

Colour

• Grey powder

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Mosaics and small tiles: 2.0–4.5 kg/m²
• Normal size tiles (20×20 cm): 4.5–9.0 kg/m²
• Large format tiles (up to 3,600 cm² internal / 2,100 cm² external): 9.0–13.5 kg/m²
• Actual coverage depends on substrate profile, tile size, and application technique. Site trials recommended.

Application Steps

• Mixing: Add powder to clean water and mix mechanically for a minimum of 3 minutes (forced action mixer or drill with paddle at <500 rpm). Leave to stand for 5 minutes, then remix for 15 seconds before use. Do not use a free-fall concrete mixer.
• Application: Apply with a notched trowel onto the substrate at a rate of ~1 m² at a time to prevent skinning. Choose trowel size to achieve the correct thickness on the tile back. Ensure no skinning occurs before bedding tiles.
• Tile Placement: Press tiles firmly into the adhesive and adjust within 30 minutes of application. For tiles larger than 30×30 cm, back-buttering is recommended.
• Cleaning: Clean tools with water before material hardens. Hardened material can only be removed mechanically.

SikaCeram®-99 Floor & Wall KH

A prepacked cementitious tile adhesive for installing ceramic, porcelain, and homogeneous tiles on floors and walls. Suitable for both interior and exterior applications as a thin or thick bed adhesive.

Overview

Specifications

Usage

• Wall and floor tile installation
• Ceramic, porcelain, and absorbing tiles
• Homogeneous tiles
• Interior and exterior use (mix with Sika® Latex for enhanced exterior adhesion)
• Thin bed or thick bed adhesive applications

Advantages

• Consistent quality and better workability
• Tile adjustable up to 20 minutes after application
• Good adhesion to concrete, cementitious mortar, stone, and bricks
• No pre-soaking of tiles required
• Compatible with Sika® Latex for increased performance
• Saves time and material cost

Packaging

• 20 kg / bag

Colour

• Grey powder (mixed to paste)

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Coverage: ~5.6–6.4 m² per 20 kg bag (based on 2 mm mortar thickness)
• Dependent on substrate profile, tile size, joint width, and application technique
• For tiles larger than 30×30 cm, buttering the back of the tile is recommended

Application Steps

• Substrate Preparation: Surface must be clean, sound, level, and free of oil or grease. Remove laitance and loose particles by sandblasting or high-pressure water jetting. Pre-wet absorbent substrates to saturated surface dry condition.
• Mixing: Add powder to ~4.0–4.6 L of clean water. Mix with a handheld or mechanical mixer for 3–5 minutes until a homogeneous, lump-free paste is achieved. Allow to stand 1–2 minutes, then re-mix for 1 minute before use.
• Application: Apply with a notched trowel onto the substrate and butter the back of the tile for better coverage. For tiles with deep grooves, ensure full coverage in the grooves. Press tiles firmly and tamp into position. Adjust within 20 minutes of application.
• Cleaning: Clean tools with water before material hardens. Hardened material can only be removed mechanically.