Stock up and keep cutting with the TAC2211005 Abrasive Metal Cutting Disc Set. This 10-piece set of 105mm ultra-thin cutting discs is built for fast, clean cuts through metal — pipes, rebar, sheet metal, angle iron, and more. At just 1.2mm thick, each disc minimises material loss and heat buildup for precise, efficient cuts every time.

Specifications

• Model: TAC2211005
• Set: 10 pcs
• Disc Diameter: 105mm
• Bore: 16mm
• Thickness: 1.2mm
• Application: Metal

Product Details

• Designed for use with 105mm (4") angle grinders
• 1.2mm ultra-thin profile – minimises material loss and reduces heat for cleaner cuts
• 16mm bore – standard fit for most 105mm angle grinders
• Suitable for cutting pipes, rebar, sheet metal, angle iron, and other metal materials
• 10-piece set – great value, always have a disc ready on the job

Materials & Care

• Application Material: Metal
• Store in a cool, dry place away from moisture and direct sunlight
• Inspect each disc for cracks or damage before use – do not use damaged discs
• Always use appropriate PPE (eye protection, gloves, face shield) when cutting
• Do not exceed the grinder's maximum rated speed

Stock up for the job site with the TAC2111003M Dry Diamond Disc Set. This 10-piece set of 100mm universal segmented diamond discs delivers fast, aggressive cutting on tile, stone, concrete, and brick — wet or dry. Packed in a durable metal box for easy storage and transport on site.

Specifications

• Model: TAC2111003M
• Set: 10 pcs
• Disc Diameter: 100mm (4")
• Bore: 16mm (5/8")
• Blade Length: 7.5mm
• Cut Type: Wet and Dry
• Application: Universal segmented, Fast Cut
• Packaging: Metal box

Product Details

• Designed for use with 100mm (4") angle grinders
• Universal segmented design – fast, aggressive cutting on tile, stone, concrete, and brick
• Fast cut performance – 7.5mm blade length for efficient material removal
• Wet and dry cutting – versatile use with or without water cooling
• 16mm (5/8") bore – standard fit for most 100mm angle grinders
• 10-piece set in metal box – great value, protected storage for job site use

Materials & Care

• Segment: Diamond (universal segmented)
• For wet cutting, always use with water to prevent overheating and extend blade life
• Store in the included metal box in a dry place
• Inspect each disc for cracks or damage before use – do not use damaged discs
• Always use appropriate PPE (eye protection, gloves, face shield) when cutting

Sikagard®-62

A 2-part, rigid, 100% solids high-build epoxy resin protective coating. Solvent-free with excellent mechanical and chemical resistance. Suitable for chemical-resistant lining of storage tanks, silos, and anti-corrosion coating on steel in food processing, sewage, agricultural, and pharmaceutical facilities. CE marked per EN 1504-2 and WRAS approved for contact with potable water.

Overview

Specifications

Mechanical Resistance (Taber Abraser)

Usage

• Chemical resistant protective layer on concrete, stone, cementitious mortars, epoxy cement, epoxy resin products, and steel
• Lining in storage tanks and silos
• Anti-corrosion coating on steel in food processing plants, sewage works, farms, agricultural enterprises, chemical and pharmaceutical facilities, and beverage industry

Advantages

• Solvent free – 100% solids
• Good mechanical and chemical resistance
• High build – ~0.2 mm per layer
• Impervious to liquids
• Easy to mix and apply
• CE marked per EN 1504-2 (concrete protection)
• WRAS approved for contact with potable water (BS 6920-1:2000)
• LEED v2009 IEQc 4.2 compliant

Packaging

• 12 kg set (Part A + Part B)

Colour

• RAL 7032 (Pebble Grey) – other colours on request

Product Details

Product Information

Pot Life

Waiting Time / Overcoating & Full Cure

Application

Application Information

Application Steps

• Substrate Preparation – Concrete: Prepare mechanically to achieve an open-textured surface. Remove weak areas, expose blowholes and voids. Remove all dust and loose material by brush and/or vacuum. Fill open voids with a suitable Sika® pore filling mortar. Level surface roughness with a suitable Sika® rendering and levelling mortar. Use a suitable primer on high-absorbent, non-sound, or non-cement-based substrates.
• Substrate Preparation – Steel: Abrasive blast clean to SSPC-SP 10 “near white metal” or Sa 2½ (ISO EN 12944-4). Prepare welds and joints per EN 14879 Part 1. Remove all dust, dirt, and blasting material. Use air-conditioning to maintain surface conditions after blast cleaning.
• Mixing: Stir Part A mechanically before use. Add all of Part B to Part A and mix continuously for 3 minutes using a low-speed stirrer (300–400 rpm) to avoid air entrapment. Pour into a clean container and stir again to ensure thorough mixing. Use only within the pot life.
• Application: Apply by brush, roller, or airless spray at ~0.30 kg/m² per layer (~0.2 mm DFT). Apply multiple coats as required within the overcoating window.
• Cleaning: Clean all tools immediately with Thinner C. Hardened/cured material can only be removed mechanically.

Sikadur®-732

A solvent-free, thixotropic 2-component structural epoxy resin adhesive. Provides a high-strength bond between new and old concrete, steel, masonry, and wood. Highly effective on dry surfaces with high early and final strength. Suitable for grouting bolts, dowels, and pins.

Overview

Specifications

Technical Information

Usage

• Bonding fresh, plastic concrete to hardened concrete and steel
• Grouting bolts, dowels, and pins
• Structural adhesive for concrete, masonry, metal, and wood

Advantages

• High strength bonding and adhesion
• Excellent adhesion to most structural materials
• High early and final strength
• Highly effective on dry surfaces
• Solvent-free

Packaging

• 5 kg set (Component A + Component B)

Colour

• Concrete grey

Product Details

Product Information

Application

Application Information

Application Steps

• Substrate Preparation: Surface must be clean and sound. May be dry or damp but free of standing water. Remove dust, laitance, grease, curing compounds, impregnations, waxes, foreign particles, and disintegrated materials. Concrete: sandblast or use other approved mechanical methods. Steel: sandblast to white metal finish (SA 2½).
• Mixing: Pre-mix each component separately. Proportion 2 parts Component A to 1 part Component B into a clean pail. Mix thoroughly for 3 minutes with a paddle on low-speed drill (400–600 rpm) until uniform in colour. Mix only the quantity that can be used within the pot life.
• Application: Apply Sikadur®-732 evenly onto the prepared substrate at 0.3–0.8 kg/m² using a brush, roller, or trowel. Place fresh concrete or structural element onto the adhesive while it is still wet and tacky. For bolt/dowel grouting, inject or pour into the hole and insert the bolt immediately.
• Important Notes: Do not exceed the pot life. Do not add solvents or thinners. Protect from rain and moisture until fully cured.

Keep your crew cutting all day with the TAC22110550 Abrasive Metal Cutting Disc Set. This bulk 50-piece set of 105mm ultra-thin cutting discs is the smart choice for high-volume metalwork — pipes, rebar, sheet metal, angle iron, and more. At just 1.2mm thick, each disc delivers fast, clean cuts with minimal material loss and heat buildup.

Specifications

• Model: TAC22110550
• Set: 50 pcs
• Disc Diameter: 105mm
• Bore: 16mm
• Thickness: 1.2mm
• Application: Metal

Product Details

• Designed for use with 105mm (4") angle grinders
• 1.2mm ultra-thin profile – minimises material loss and reduces heat for cleaner cuts
• 16mm bore – standard fit for most 105mm angle grinders
• Suitable for cutting pipes, rebar, sheet metal, angle iron, and other metal materials
• 50-piece bulk set – ideal for job sites, workshops, and high-volume cutting tasks

Materials & Care

• Application Material: Metal
• Store in a cool, dry place away from moisture and direct sunlight
• Inspect each disc for cracks or damage before use – do not use damaged discs
• Always use appropriate PPE (eye protection, gloves, face shield) when cutting
• Do not exceed the grinder's maximum rated speed

Angle Grinder 1100W TOTAL TG11012556

1100W angle grinder with 125mm (5″) disc capacity, M14 spindle thread, and 12,000rpm no-load speed for grinding, cutting, and surface finishing on metal and masonry. Includes auxiliary side handle. 220–240V / 50–60Hz.

Note: Disc not included.

Specifications

Features

• 1100W motor for grinding, cutting, and surface finishing on metal and masonry
• 12,000rpm no-load speed for fast, efficient material removal
• 125mm disc capacity for versatile applications
• M14 spindle thread for wide disc compatibility
• Auxiliary side handle included for improved control and stability

Package Contents

• 1 pc Angle Grinder 1100W (TG11012556)
• 1 pc Auxiliary side handle

Angle Grinder 1500W TOTAL TG11512536

Heavy-duty 1500W angle grinder with 125mm (5″) disc capacity, M14 spindle thread, and 9,300rpm no-load speed for demanding grinding, cutting, and surface finishing on metal and masonry. Includes auxiliary side handle and extra carbon brushes. 220–240V / 50–60Hz.

Note: Disc not included.

Specifications

Features

• 1500W motor for demanding grinding, cutting, and surface finishing
• 9,300rpm no-load speed for fast, efficient material removal
• 125mm disc capacity for versatile applications on metal and masonry
• M14 spindle thread for wide disc compatibility
• Auxiliary side handle included for improved control and stability

Package Contents

• 1 pc Angle Grinder 1500W (TG11512536)
• 1 pc Auxiliary side handle
• 1 set Extra carbon brushes

Angle Grinder 2000W TOTAL TG12018026

Industrial-grade 2000W angle grinder with 180mm (7″) disc capacity, M14 spindle thread, and 8,450rpm no-load speed for heavy-duty grinding, cutting, and surface finishing on metal and masonry. Includes auxiliary side handle, spanner, and extra carbon brushes. 220–240V / 50–60Hz.

Note: Disc not included.

Specifications

Features

• 2000W industrial motor for heavy-duty grinding, cutting, and surface finishing
• 8,450rpm no-load speed for fast, efficient material removal
• 180mm disc capacity for versatile applications on metal and masonry
• M14 spindle thread for wide disc compatibility
• Auxiliary side handle and spanner included for improved control

Package Contents

• 1 pc Angle Grinder 2000W (TG12018026)
• 1 pc Auxiliary side handle
• 1 pc Spanner
• 1 set Extra carbon brushes (free)

Angle Grinder 2400W TOTAL TG1252306

Heavy-duty 2400W angle grinder with 230mm (9″) disc capacity, M14 spindle thread, and 6,400rpm no-load speed for demanding grinding, cutting, and surface finishing on metal and masonry. Includes auxiliary side handle and extra carbon brushes. 220–240V / 50–60Hz.

Note: Disc not included.

Specifications

Features

• 2400W heavy-duty motor for demanding grinding, cutting, and surface finishing
• 6,400rpm no-load speed for fast, efficient material removal
• 230mm disc capacity for wide coverage on metal and masonry
• M14 spindle thread for wide disc compatibility
• Auxiliary side handle included for improved control and stability

Package Contents

• 1 pc Angle Grinder 2400W (TG1252306)
• 1 pc Auxiliary side handle
• 1 set Extra carbon brushes

Angle Grinder 3000W TOTAL TG1302306

Heavy-duty 3000W angle grinder with 230mm (9″) disc capacity, M14 spindle thread, and 6,300rpm no-load speed for the most demanding grinding, cutting, and surface finishing tasks on metal and masonry. Includes auxiliary side handle and extra carbon brushes. 220–240V / 50–60Hz.

Note: Disc not included.

Specifications

Features

• 3000W heavy-duty motor for the most demanding grinding and cutting applications
• 6,300rpm no-load speed for fast, efficient material removal
• 230mm disc capacity for wide coverage on metal and masonry
• M14 spindle thread for wide disc compatibility
• Auxiliary side handle included for improved control and stability

Package Contents

• 1 pc Angle Grinder 3000W (TG1302306)
• 1 pc Auxiliary side handle
• 1 set Extra carbon brushes

Angle Grinder 710W 100mm

710W corded angle grinder with 100mm (4") disc diameter, 12,000rpm no-load speed, and M10 spindle thread. Features auxiliary side handle and safety guard for controlled and safe grinding, cutting, and polishing. Model: Jadever JDAG35712.

Specifications

Features

• 710W motor for grinding, cutting, and polishing metal, stone, and masonry
• 12,000rpm high speed for fast and efficient material removal
• 100mm (4") disc for compact and maneuverable grinding in tight spaces
• M10 spindle thread for compatibility with standard 100mm grinding and cutting discs
• Auxiliary side handle for improved grip and two-handed control
• Safety guard for operator protection during grinding and cutting
• Compact and lightweight design for easy one-handed operation

Angle Grinder 710W TOTAL TG10710076

Industrial-grade 710W angle grinder with 100mm (4″) disc capacity, M10 spindle thread, and 12,000rpm no-load speed. Features a rear-mounted ON/OFF toggle switch for safe operation. Includes auxiliary side handle and spanner. 220–240V / 50–60Hz.

Note: Cutting disc not included.

Specifications

Features

• 710W industrial motor for grinding, cutting, and surface finishing
• 12,000rpm no-load speed for fast, efficient material removal
• 100mm disc capacity for versatile applications on metal and masonry
• Rear-mounted ON/OFF toggle switch for safe, convenient operation
• Auxiliary side handle included for improved control and stability

Package Contents

• 1 pc Angle Grinder 710W (TG10710076)
• 1 pc Auxiliary side handle
• 1 pc Spanner

Angle Grinder 750W TOTAL TG10710056

Industrial-grade 750W angle grinder with 100mm (4″) disc capacity, M10 spindle thread, and 12,000rpm no-load speed. Features a rear-mounted ON/OFF toggle switch for safe operation. Includes flat spanner. 220–240V / 50–60Hz.

Note: Cutting disc not included.

Specifications

Features

• 750W industrial motor for grinding, cutting, and surface finishing
• 12,000rpm no-load speed for fast, efficient material removal
• 100mm disc capacity for versatile applications on metal and masonry
• Rear-mounted ON/OFF toggle switch for safe, convenient operation
• M10 spindle thread for wide disc compatibility

Package Contents

• 1 pc Angle Grinder 750W (TG10710056)
• 1 pc Flat spanner

Angle Grinder 850W 125mm

850W corded angle grinder with 125mm (5") disc diameter, 12,000rpm no-load speed, and M14 spindle thread. Features lock-on button for continuous operation, auxiliary side handle, and safety guard for controlled and safe grinding, cutting, and polishing. Model: Jadever JDAG15851.

Specifications

Features

• 850W motor for grinding, cutting, and polishing metal, stone, and masonry
• 12,000rpm high speed for fast and efficient material removal
• 125mm (5") disc for greater cutting depth and coverage vs 100mm models
• M14 spindle thread for compatibility with standard 125mm grinding and cutting discs
• Lock-on button for continuous operation without holding the trigger
• Auxiliary side handle for improved grip and two-handed control
• Safety guard for operator protection during grinding and cutting

Angle Grinder 900W TOTAL TG10910056

Industrial-grade 900W angle grinder with 100mm (4″) disc capacity, M10 spindle thread, and 12,000rpm no-load speed. Features a rear-mounted ON/OFF toggle switch. Includes auxiliary side handle, disc guard, and spanner. 220–240V / 50–60Hz.

Note: Cutting disc not included.

Specifications

Features

• 900W industrial motor for grinding, cutting, and surface finishing
• 12,000rpm no-load speed for fast, efficient material removal
• 100mm disc capacity for versatile applications on metal and masonry
• Rear-mounted ON/OFF toggle switch for convenient operation
• M10 spindle thread with disc guard and auxiliary handle included

Package Contents

• 1 pc Angle Grinder 900W (TG10910056)
• 1 pc Auxiliary side handle
• 1 pc Disc guard
• 1 pc Spanner

Self-Priming Jet Pump 1100W TOTAL TWP311006

The TOTAL TWP311006 is a 1100W (1.5HP) self-priming jet pump with a 100% copper wire motor, stainless steel impeller, and electrophoresis pump body. Delivers 60m max head, 70L/min max flow, and 9m max suction for high-demand water supply applications.

Specifications

Product Features

• Self-priming design for easy startup without manual priming
• 1100W (1.5HP) powerful motor for high-demand water supply applications
• 100% copper wire motor for efficient, long-lasting operation
• Stainless steel impeller and shaft for corrosion resistance and durability
• Electrophoresis pump body for superior rust and corrosion protection
• 60m max head for pumping water to elevated tanks or upper floors
• 9m max suction depth for versatile installation

SikaShield P24 MG 4.5 kg/m²

SikaShield P24 MG is an APP modified bituminous roof waterproofing membrane by Sika, reinforced with non-woven polyester fabric. The mineral granule top surface provides permanent UV resistance and a decorative finish, torch-applied via burn-off film for a fully bonded, seamless installation.

Specifications

Product Features

• Decorative mineral granules — UV resistant for permanent outdoor exposure
• Torch-applied via burn-off film for easy, fully bonded installation
• Flexible at 0°C — suitable for varying temperature conditions
• Good mechanical properties: tensile, tear, and shear resistance
• Can be painted immediately after application
• Tiles can be placed directly onto the membrane
• Suitable for flat or sloping roofs (up to 15% gradient), balconies, and terraces
• Use as exposed cap sheet in a multi-layer waterproofing system

Application Steps

• Substrate Preparation: Surface must be uniform, firm, smooth, and free from sharp protrusions, grease, laitance, oil, dust, and loose particles. Must be clean and dry.
• Alignment: Unroll and align the membrane, then re-roll before application. Lay membranes parallel to avoid coinciding joints. When applying over another bituminous membrane, straddle the overlaps of the previous layer.
• Torching: Heat the substrate and the burn-off film with a gas burner. When the backing film starts to melt, roll the membrane forward and press firmly. Keep the flame moving to avoid overheating (polyester reinforcement melts at +260°C). A bead of melted bitumen must be visible along all overlaps.
• Overlaps: Overlap sides by min. 100 mm and ends by min. 150 mm. At end overlaps, cut a 100×100 mm corner at 45°. Weld until a 10 mm trickle of melted mixture is visible along the overlap line.
• Detailing: Use a sharp knife to cut around corners, upstands, vent pipes, drains, and support metalwork. Use flat-profile footwear only — spikes may puncture the membrane.

SikaShield® P24 S 3mm

An APP modified bituminous waterproofing membrane reinforced with non-woven polyester fabric. The sand top surface ensures excellent bond for overlying layers. Torch-applied via burn-off film on the underside for a fully bonded installation. Flexible at 0°C and suitable as a base sheet in multi-layer systems under protective layers, tiles, or ballast.

Overview

Specifications

Usage

• Waterproofing membrane for balconies and terraces under heavy protection layers (tiles or gravel)
• Flat and sloping roofs under protective layers or ballast
• Car park decks
• Wet areas
• Basements and below-ground structures
• Horizontal reinforced concrete slabs, decks, podiums, and protrusions
• Vertical reinforced concrete walls
• Base sheet in multi-layer waterproofing systems
• Note: Not suitable for roofs permanently exposed to UV radiation

Advantages

• Easy to install by torching method
• Fully bonded application
• Flexible in cold temperatures (0°C)
• Good durability and mechanical properties (tensile, tear, shear)
• Can be painted immediately after application
• Insulation panels can be bonded directly without special adhesives or mechanical fixings
• Sand surface ensures excellent bond for overlying layers

Packaging

• 1 roll = 1.0 m wide × 10.0 m long (10 m²)

Colour

• Top surface: Sand
• Bottom surface: Polyethylene film

Product Details

Product Information

Application

Application Information

Application Steps

• Substrate Preparation: Surface must be uniform, firm, smooth, and free from sharp protrusions, grease, laitance, oil, dust, and loose particles. Must be clean and dry.
• Priming: Apply the appropriate Sika® primer at the required consumption onto the prepared dry surface. Allow the primer to dry completely before membrane installation. Contact Sika Technical Service for primer selection guidance.
• Alignment: Unroll the membrane and align it. Re-roll before application. Lay membranes parallel to avoid coinciding joints. When applying over another bituminous membrane, straddle the overlaps of the previous layer.
• Torching: Heat the substrate and the burn-off film on the underside of the membrane with a gas burner. When the backing film starts to melt, roll the membrane forward and press firmly against the substrate. Keep the flame moving to avoid overheating (polyester reinforcement melts at +260°C). A bead of melted bitumen must be visible along the full length of all overlaps.
• Overlaps: Overlap sides by min. 100 mm and ends by min. 150 mm. At end overlaps, cut a 100×100 mm corner at 45°. Weld overlaps until a 10 mm trickle of melted mixture is visible along the overlap line.
• Detailing: Use a sharp knife to cut around internal/external corners, upstands, vent pipes, drains, and support metalwork. Refer to the relevant method statement for detailing guidance.
• Suitable Substrates for Torching: Concrete, perlite screed, bituminous membranes with smooth surface, compatible coatings, brick masonry, cementitious screeds.
• Footwear: Use flat-profile footwear only – spikes or sharp protrusions may puncture the membrane.

SikaShield® P24 S 4mm

An APP modified bituminous waterproofing membrane reinforced with non-woven polyester fabric. The sand top surface ensures excellent bond for overlying layers. Torch-applied via burn-off film on the underside for a fully bonded installation. Flexible at 0°C and suitable as a base sheet in multi-layer systems under protective layers, tiles, or ballast.

Overview

Specifications

Usage

• Waterproofing membrane for balconies and terraces under heavy protection layers (tiles or gravel)
• Flat and sloping roofs under protective layers or ballast
• Car park decks
• Wet areas
• Basements and below-ground structures
• Horizontal reinforced concrete slabs, decks, podiums, and protrusions
• Vertical reinforced concrete walls
• Base sheet in multi-layer waterproofing systems
• Note: Not suitable for roofs permanently exposed to UV radiation

Advantages

• Easy to install by torching method
• Fully bonded application
• Flexible in cold temperatures (≤0°C)
• Good durability and mechanical properties (tensile, tear, shear)
• Can be painted immediately after application
• Insulation panels can be bonded directly without special adhesives or mechanical fixings
• Sand surface ensures excellent bond for overlying layers

Packaging

• 1 roll = 1.0 m wide × 10.0 m long (10 m²)

Colour

• Top surface: Sand
• Bottom surface: Polyethylene film

Product Details

Product Information

Application

Application Information

Application Steps

• Substrate Preparation: Surface must be uniform, firm, smooth, and free from sharp protrusions, grease, laitance, oil, dust, and loose particles. Must be clean and dry.
• Priming: Apply the appropriate Sika® primer at the required consumption onto the prepared dry surface. Allow the primer to dry completely before membrane installation. Contact Sika Technical Service for primer selection guidance.
• Alignment: Unroll the membrane and align it. Re-roll before application. Lay membranes parallel to avoid coinciding joints. When applying over another bituminous membrane, straddle the overlaps of the previous layer.
• Torching: Heat the substrate and the burn-off film on the underside of the membrane with a gas burner. When the backing film starts to melt, roll the membrane forward and press firmly against the substrate. Keep the flame moving to avoid overheating (polyester reinforcement melts at +260°C). A bead of melted bitumen must be visible along the full length of all overlaps.
• Overlaps: Overlap sides by min. 100 mm and ends by min. 150 mm. At end overlaps, cut a 100×100 mm corner at 45°. Weld overlaps until a 10 mm trickle of melted mixture is visible along the overlap line.
• Detailing: Use a sharp knife to cut around internal/external corners, upstands, vent pipes, drains, and support metalwork. Refer to the relevant method statement for detailing guidance.
• Suitable Substrates for Torching: Concrete, perlite screed, bituminous membranes with smooth surface, compatible coatings, brick masonry, cementitious screeds.
• Footwear: Use flat-profile footwear only – spikes or sharp protrusions may puncture the membrane.

Maintenance

• Check the functionality of auxiliary works, flashings, drainage outlets, and overflow pipes regularly.
• Remove leaves, moss, and vegetation that could cause ponding and overload the drainage system.
• Arrange periodic inspections of the membrane and detailing to maintain waterproofing performance throughout its lifespan.

Automatic Pump Control 10bar TOTAL TWPS101

Automatic pump control switch with 1.5 bar starting pressure and 10 bar (145 psi) max pressure. Rated at 1100W / 10A with IP65 protection for outdoor and wet environment use. Fits 1" pipe diameter. Model: TOTAL TWPS101.

Specifications

Features

• Automatic start/stop control — activates pump at 1.5 bar and cuts off at max pressure
• 10 bar (145 psi) max pressure for a wide range of water pump applications
• IP65 protection rating for safe use in outdoor and wet environments
• Max 60°C water temperature tolerance
• 1" pipe diameter for standard pump connection
• 1100W / 10A rated for compatibility with most domestic and light industrial pumps

Automatic Pump Control 10bar TOTAL TWPS102

Automatic pump control switch with 1.5 bar starting pressure and 10 bar max pressure. Rated at 1100W / 10A with IP65 protection for outdoor and wet environment use. Fits 1" pipe diameter. Model: TOTAL TWPS102.

Specifications

Features

• Automatic start/stop control — activates pump at 1.5 bar and cuts off at max pressure
• 10 bar max pressure for a wide range of water pump applications
• IP65 protection rating for safe use in outdoor and wet environments
• 1" pipe diameter for standard pump connection
• 1100W / 10A rated for compatibility with most domestic and light industrial pumps

Automatic Self-Priming Peripheral Pump 370W TOTAL TWP93706

The TOTAL TWP93706 is a 370W (0.5HP) automatic self-priming peripheral pump with a 100% copper wire motor, brass impeller, and integrated pressure tank. Delivers 35m max head and 35L/min max flow with 8m max suction. IPX4 rated with built-in thermal protector.

Specifications

Product Features

• Automatic self-priming with integrated pressure tank for consistent water pressure
• 100% copper wire motor for efficient, long-lasting operation
• Brass impeller for durability and smooth water flow
• Electrophoresis pump body for superior rust and corrosion protection
• Built-in thermal protector to prevent motor burnout from overheating
• IPX4 splash-proof protection for safe outdoor installation
• 35m max head for pumping water to elevated tanks or upper floors

Automatic Self-Priming Peripheral Pump 750W TOTAL TWP97505

The TOTAL TWP97505 is a 750W (1.0HP) automatic self-priming peripheral pump with a 100% copper wire motor and integrated pressure tank for consistent water pressure. Ideal for household and light commercial water supply applications.

Specifications

Product Features

• Automatic self-priming with integrated pressure tank for consistent water pressure
• 100% copper wire motor for efficient, long-lasting operation
• 750W (1.0HP) powerful motor for household and light commercial water supply
• 220–240V rated for standard household power supply

SikaShield® W159 ED 1.5mm

A polymer modified bituminous waterproofing membrane wet-applied to concrete using adhesive mortar SikaShield® W1. Flame-free installation makes it safe for confined spaces. Reinforced with cross-laminated PE film for high mechanical performance. Fully bonded and watertight against lateral water migration. Can be applied on wet concrete.

Overview

Specifications

Usage

• Basements and below-ground structures
• Vertical reinforced concrete walls
• Single and strip foundations
• Single layer under heavy protection
• Base sheet in multi-layer waterproofing systems
• Note: Not suitable for roofs permanently exposed to UV radiation

Advantages

• No-torch application – safe for confined spaces
• Fully bonded system for reliable waterproofing
• Watertight against lateral water migration (70 m resistance)
• Can be applied on wet concrete
• Fast and easy installation
• Flame-free application
• Requires minimal surface preparation
• High impact resistance (240 N static puncture)

Packaging

• 1 roll = 1.0 m wide × 20.0 m long (20 m²)

Colour

• Top and bottom surface: Removable foil liner

Product Details

Product Information

Application

Application Information

Application Steps

• Substrate Preparation: Apply adhesive mortar SikaShield® W1 onto the water-saturated concrete substrate while still wet. Refer to the SikaShield® W1 PDS for full substrate condition requirements.
• Alignment: Unroll the membrane and align it. Re-roll before application. Lay membranes parallel to avoid coinciding joints. When applying over another bituminous membrane, straddle the overlaps of the previous layer.
• Wet Application: Lay the membrane directly over the wet adhesive mortar. At one end, peel away part of the release liner from the underside. Bond this end to the adhesive and substrate. Continue peeling the liner sideways while bonding the rest of the membrane.
• Rolling: Roll the applied membrane surface with a roller from the centre to the edge to remove air bubbles. Push any excess adhesive towards the opposite direction of the sealed side overlap.
• Overlap Sealing: If ambient temperature is below +10°C, seal membrane overlaps by heating with a gas torch or hot air to ensure proper adhesion and prevent adhesive trapping under the overlap.
• Curing & Backfilling: Allow adhesive mortar to cure for at least 24 hours at +25°C before backfilling. Complete backfilling within 7 days of application.
• Detailing: Use a sharp knife to cut around internal/external corners, upstands, vent pipes, drains, and support metalwork. Refer to the relevant method statement for detailing guidance.
• Footwear: Use flat-profile footwear only – spikes or sharp protrusions may puncture the membrane.

Brushless Cordless Rotary Hammer 20V 22mm

20V P20S brushless cordless rotary hammer with 22mm (7/8") max drilling capacity, 4 functions, 0–1,100rpm no-load speed, and 0–5,400bpm impact rate. SDS-Plus chuck for quick bit changes. Includes 1× 3.0Ah battery, charger, SDS-Plus drill bit set, and Jadever carry case. Model: Jadever JDLM1522.

Specifications

Features

• Brushless motor for higher efficiency, longer runtime, and extended tool life
• P20S platform — compatible with other Jadever 20V SHARE Li-ion batteries
• 4 functions: drill, hammer drill, chisel, and chisel lock for versatile applications
• 22mm (7/8") max drilling capacity in concrete for heavy-duty masonry work
• SDS-Plus chuck for fast, tool-free bit changes
• 0–5,400bpm impact rate for effective chiseling and concrete drilling
• Auxiliary side handle for improved grip and control
• SDS-Plus drill bit set included for immediate use
• Jadever carry case for safe storage and transport

Package Contents

• 1 pc Brushless cordless rotary hammer
• 1 pc 20V 3.0Ah Li-ion battery
• 1 pc Charger
• 1 set SDS-Plus drill bits
• 1 pc Jadever carry case

Brushless Cordless Rotary Hammer 20V 26mm

20V P20S brushless cordless rotary hammer with 26mm (1") max drilling capacity, 4 functions, 0–1,100rpm no-load speed, and 0–5,000bpm impact rate. SDS-Plus chuck for quick bit changes. Includes 2× 4.0Ah batteries, charger, SDS-Plus drill bit set, and Jadever carry case. Model: Jadever JDLM1B262.

Specifications

Features

• Brushless motor for higher efficiency, longer runtime, and extended tool life
• P20S platform — compatible with other Jadever 20V SHARE Li-ion batteries
• 4 functions: drill, hammer drill, chisel, and chisel lock for versatile applications
• 26mm (1") max drilling capacity in concrete for heavy-duty masonry work
• SDS-Plus chuck for fast, tool-free bit changes
• 0–5,000bpm impact rate for effective chiseling and concrete drilling
• Auxiliary side handle for improved grip and control
• 2× 4.0Ah high-capacity batteries for maximum runtime
• SDS-Plus drill bit set included for immediate use
• Jadever carry case for safe storage and transport

Package Contents

• 1 pc Brushless cordless rotary hammer
• 2 pcs 20V 4.0Ah Li-ion battery
• 1 pc Charger
• 1 set SDS-Plus drill bits
• 1 pc Jadever carry case

Centrifugal Pump 1500W 2" TOTAL TWP2150026

The TOTAL TWP2150026 is a 1500W (2.0HP) centrifugal pump with a 100% copper wire motor, stainless steel impeller, and 2" pipe diameter for high-volume water transfer. Delivers 450L/min max flow and 18m max head with 8m max suction — ideal for industrial drainage and irrigation.

Specifications

Product Features

• 1500W (2.0HP) powerful motor for high-volume industrial water transfer
• 450L/min massive flow rate for fast drainage and irrigation applications
• 100% copper wire motor for efficient, long-lasting operation
• Stainless steel impeller and shaft for corrosion resistance and durability
• Electrophoresis pump body for superior rust and corrosion protection
• 2" pipe diameter for high-volume water discharge
• 8m max suction depth for versatile installation

Centrifugal Pump 1500W TOTAL TWP215006

The TOTAL TWP215006 is a 1500W (2.0HP) centrifugal pump with a 100% copper wire motor, stainless steel impeller, and electrophoresis pump body. Delivers 45m max head and 140L/min max flow with 8m max suction. IPX4 rated with built-in thermal protector for safe outdoor installation.

Specifications

Product Features

• 1500W (2.0HP) powerful motor for high-demand water supply applications
• 100% copper wire motor for efficient, long-lasting operation
• Stainless steel impeller for corrosion resistance and durability
• Electrophoresis pump body for superior rust and corrosion protection
• Built-in thermal protector to prevent motor burnout from overheating
• 45m max head for pumping water to elevated tanks or upper floors
• IPX4 splash-proof protection for safe outdoor installation