Safety Helmet

The JADEVER JDSH1303 is a lightweight 100% new PE safety helmet designed for construction and industrial use. Featuring a 6-point suspension system and adjustable buckle, it delivers reliable head protection with all-day comfort.

Specifications

Product Features

• 100% new PE shell for reliable impact protection on construction and industrial sites
• 6-point suspension system for even load distribution and enhanced comfort
• Adjustable head size via buckle for a secure, customizable fit
• Chin strap included for added stability during active use
• Lightweight at only 320g for all-day wearability
• Ventilation slots for improved airflow and comfort in hot environments
• Separate shell and inner harness design for easy cleaning and replacement

Safety Helmet Vented PE 6-Point — TOTAL TSP8602

Lightweight 380g safety helmet made from 100% new PE with top vents for breathability on hot job sites. Features a 6-point V-type suspension harness for a comfortable, secure fit. Builder-safe rated for construction and industrial use.

Specifications

What's in the Box

• 1× TOTAL Safety Helmet (TSP8602)

Materials & Care

• Shell: 100% new PE — impact and penetration resistant
• Inspect shell and harness before each use; replace if cracked or damaged
• Clean with mild soap and water; avoid solvents that degrade PE
• Replace helmet after any significant impact, even if no visible damage
• Do not store in direct sunlight for extended periods — UV degrades PE over time

Screw Pump 3" 750W TOTAL TSWP7501

The TOTAL TSWP7501 is a 750W (1.0HP) 3" submersible screw pump with a full stainless steel body and 100% copper wire motor. It delivers up to 103m max head and 33L/min flow — ideal for narrow 3" boreholes and deep well water supply. Includes 9m cable.

Specifications

Product Features

• 100% copper wire motor for maximum efficiency and long service life
• Full stainless steel pump body for superior corrosion resistance
• 103m max head — ideal for pumping to elevated storage tanks
• 3" slim body fits standard 3" boreholes and deep wells
• 1" discharge outlet for standard pipe connection
• 9m cable included for deep submersion installation

Convert your SDS Plus rotary hammer into a powerful core drilling machine with the TAC43A13501 SDS Plus Adaptor. At 350mm long with an M22 thread, this adaptor connects TOTAL TCT hole core bits (50mm–100mm) directly to any SDS Plus hammer drill — no dedicated core drill machine required. Includes an 8×110mm masonry pilot bit for accurate hole starting.

Specifications

• Model: TAC43A13501
• Shank: SDS Plus
• Thread: M22
• Length: 350mm
• Includes: 1 pc 8×110mm masonry drill bit
• Compatible Core Bits: TAC430501 (50mm), TAC430651 (65mm), TAC430801 (80mm), TAC431001 (100mm)
• Packaging: Plastic tube

Product Details

• SDS Plus shank – fits any standard SDS Plus rotary hammer drill for tool-free connection
• M22 thread – compatible with TOTAL TCT hole core bits (50–100mm diameter)
• 350mm length – provides the reach needed for deep core drilling through walls and slabs
• 8×110mm masonry pilot bit included – centres the core bit for accurate, clean holes
• Eliminates the need for a dedicated core drilling machine for medium-diameter holes

Materials & Care

• Shank: SDS Plus
• Thread: M22
• Store in the included plastic tube to protect threads and shank
• Keep threads clean and free of debris for secure core bit connection
• Inspect shank and thread before each use – do not use if damaged
• Use only with compatible SDS Plus rotary hammer drills

Grind, shape, and surface concrete, stone, and masonry with precision using the TAC2411251 Segmented Turbo Cup Grinding Wheel. This 125mm cup wheel features a segmented turbo design for aggressive material removal with efficient dust evacuation — ideal for surface preparation, levelling, and edge grinding on hard materials.

Specifications

• Model: TAC2411251
• Diameter: 125mm
• Blade Width: 20mm
• Arbor: 22.22mm
• Packaging: Color box

Product Details

• Designed for use with 125mm (5") angle grinders
• Segmented turbo design – aggressive grinding with efficient dust and debris removal between segments
• 22.22mm arbor – standard fit for most 125mm angle grinders
• Suitable for surface preparation, levelling, edge grinding, and material removal on concrete, stone, brick, and masonry
• 20mm blade width for stable, controlled grinding contact

Materials & Care

• Segment: Diamond (segmented turbo)
• Store in a cool, dry place away from moisture and direct sunlight
• Inspect wheel for cracks or damage before each use – do not use damaged wheels
• Always use appropriate PPE (eye protection, gloves, face shield, dust mask) when grinding
• Do not exceed the grinder's maximum rated speed

Self-Priming Jet Pump 1100W 1.5HP

1100W (1.5HP) self-priming jet pump with 55m max head, 63L/min max flow, and 9m max suction depth. Cast iron pump body for durability and corrosion resistance. 1"×1" inlet/outlet ports for standard pipe connections. Suitable for domestic water supply, garden irrigation, and water transfer applications. Model: Jadever JDWPJA04.

Specifications

Features

• 1100W (1.5HP) motor for reliable and powerful water pumping
• Self-priming design for easy startup without manual priming
• 55m max head for pumping water to elevated tanks and upper floors
• 63L/min max flow for fast water transfer and irrigation
• 9m max suction depth for drawing water from wells and tanks
• 1"×1" inlet/outlet ports for standard pipe connections
• Cast iron pump body for durability and long service life
• Base mounting feet for secure installation on flat surfaces
• Suitable for domestic water supply, garden irrigation, and water transfer

Self-Priming Jet Pump 1500W TOTAL TWP315006

The TOTAL TWP315006 is a 1500W (2.0HP) self-priming jet pump with a 100% copper wire motor, stainless steel impeller, and electrophoresis pump body. Delivers 60m max head, 100L/min max flow, and 9m max suction for high-demand water supply applications.

Specifications

Product Features

• Self-priming design for easy startup without manual priming
• 1500W (2.0HP) powerful motor for high-demand water supply applications
• 100% copper wire motor for efficient, long-lasting operation
• Stainless steel impeller for corrosion resistance and durability
• Stainless steel welded shaft (304+45#) for strength and corrosion resistance
• Electrophoresis pump body for superior rust and corrosion protection
• 60m max head for pumping water to elevated tanks or upper floors
• 9m max suction depth for versatile installation

Self-Priming Jet Pump 750W 1HP

750W (1.0HP) self-priming jet pump with 45m max head, 50L/min max flow, and 9m max suction depth. Cast iron pump body for durability and corrosion resistance. 1"×1" inlet/outlet ports for standard pipe connections. Suitable for domestic water supply, garden irrigation, and water transfer applications. Model: Jadever JDWPJA03.

Specifications

Features

• 750W (1.0HP) motor for reliable and powerful water pumping
• Self-priming design for easy startup without manual priming
• 45m max head for pumping water to elevated tanks and upper floors
• 50L/min max flow for fast water transfer and irrigation
• 9m max suction depth for drawing water from wells and tanks
• 1"×1" inlet/outlet ports for standard pipe connections
• Cast iron pump body for durability and long service life
• Base mounting feet for secure installation on flat surfaces
• Suitable for domestic water supply, garden irrigation, and water transfer

Self-Priming Jet Pump 750W TOTAL TWP37506

The TOTAL TWP37506 is a 750W (1.0HP) self-priming jet pump with a 100% copper wire motor, stainless steel impeller, and electrophoresis pump body. Delivers 51m max head, 55L/min max flow, and 9m max suction for reliable household and commercial water supply.

Specifications

Product Features

• Self-priming design for easy startup without manual priming
• 100% copper wire motor for efficient, long-lasting operation
• Stainless steel impeller and shaft for corrosion resistance and durability
• Electrophoresis pump body for superior rust and corrosion protection
• 51m max head for pumping water to elevated tanks or upper floors
• 9m max suction depth for versatile installation

Self-Priming Jet Pump 750W TOTAL TWPS375062

The TOTAL TWPS375062 is a 750W (1.0HP) stainless steel self-priming jet pump with a 100% copper wire motor, full stainless steel pump head, and stainless steel impeller. Delivers 40m max head and 55L/min max flow with 8m max suction.

Specifications

Product Features

• Full stainless steel pump head for maximum corrosion resistance and hygiene
• Stainless steel impeller for long-lasting durability in clean water applications
• 100% copper wire motor for efficient, reliable continuous operation
• Self-priming design for easy startup without manual priming
• 40m max head for pumping water to elevated tanks or upper floors
• 8m max suction depth for versatile installation

Sika AnchorFix®-2+ Tropical

A solvent and styrene-free, 2-component epoxy acrylate anchoring adhesive designed for medium to high load applications in hot and tropical climatic conditions. Fast curing, non-sag even overhead, and compatible with standard dispensing guns.

Overview

Specifications

Usage

• Chemical anchoring in solid concrete and masonry
• Anchoring of threaded rods and reinforcement bars
• Medium to high load structural fixings
• Suitable for hot and tropical climatic conditions

Advantages

• Fast curing – ready for loading in as little as 40 minutes at +35°C to +40°C
• Solvent and styrene free
• Non-sag – suitable for vertical and overhead applications
• Compatible with standard dispensing guns
• Medium to high load capacity
• Formulated for tropical and high-temperature environments

Packaging

• 300 ml / 490 g cartridge (A+B)

Colour

• Grey (mixed)

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Consumption depends on anchor diameter, embedment depth, and substrate type. Refer to Sika Technical Documentation Ref: 870 43 07 for design details.
• Pump approximately twice until both components come out uniformly before starting application.

Application Steps

• Cartridge Preparation (300 ml, 550 ml, 850 ml): Unscrew cap → Cut film → Screw on static mixer → Place in dispenser and start application.
• Cartridge Preparation (350 ml, 825 ml): Unscrew cap → Remove cap → Screw on static mixer → Place in dispenser and start application.
• Substrate Quality: Concrete and mortar must be older than 28 days. Verify substrate strength; perform pull-out tests if unknown.
• Hole Preparation: Drill hole to required diameter and depth. Clean hole with blow pump or oil-free compressed air from the bottom (min. 2x). Brush with special steel brush (min. 2x, brush diameter larger than hole). Repeat blow cleaning (min. 2x). Hole must be clean, dry, and free from oil and grease. Clean threaded rods and reinforcement bars thoroughly.
• Priming: Pump adhesive twice until both parts come out uniformly. Release gun pressure and clean cartridge opening with a cloth.
• Injection: Inject adhesive from the bottom of the hole while slowly drawing back the static mixer. Avoid entrapping air. Use extension tubing for deep holes.
• Anchor Insertion: Insert anchor with a rotary motion into the filled hole within the open time. Some adhesive must come out of the hole. Do not move or load the anchor during curing time.
• Cleaning: Clean all tools immediately with Sika® Colma Cleaner. Wash hands with warm soap water. Hardened material can only be removed mechanically.

SikaCeram®-188 KH

A high performance, thin layer cementitious tile adhesive (C2TE) for bonding ceramic, porcelain, and mosaic tiles on floors and walls. Suitable for interior and exterior use with excellent slip resistance and extended open time.

Overview

Specifications

Usage

• Ceramic, porcelain, and homogeneous tiles
• All types of low and high absorption tiles
• Mosaics of every type
• Large format tiles and under-floor heating systems
• Tile-on-tile refurbishment (walls and floors)
• Interior painted walls (if paint coating is well bonded and sound)
• Substrates: concrete, mortar, bricks, tiled surfaces
• Interior and exterior, walls and floors

Advantages

• Easy to use with excellent workability and thixotropic consistency
• No sagging or tile slip on vertical surfaces, even with heavy tiles
• Very good adhesion to most common substrates and existing tiles
• Extended open time and adjustability
• Tile-on-tile refurbishment system compatible
• Compatible with Sikalastic®-1K, SikaTop® Seal-107, and SikaTop® Seal-109

Packaging

• 20 kg / bag

Colour

• Grey powder

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Mosaics and small tiles: 2.0–4.5 kg/m²
• Normal size tiles (20×20 cm): 4.5–9.0 kg/m²
• Large format tiles (up to 3,600 cm² internal / 2,100 cm² external): 9.0–13.5 kg/m²
• Actual coverage depends on substrate profile, tile size, and application technique. Site trials recommended.

Application Steps

• Mixing: Add powder to clean water and mix mechanically for a minimum of 3 minutes (forced action mixer or drill with paddle at <500 rpm). Leave to stand for 5 minutes, then remix for 15 seconds before use. Do not use a free-fall concrete mixer.
• Application: Apply with a notched trowel onto the substrate at a rate of ~1 m² at a time to prevent skinning. Choose trowel size to achieve the correct thickness on the tile back. Ensure no skinning occurs before bedding tiles.
• Tile Placement: Press tiles firmly into the adhesive and adjust within 30 minutes of application. For tiles larger than 30×30 cm, back-buttering is recommended.
• Cleaning: Clean tools with water before material hardens. Hardened material can only be removed mechanically.

SikaCeram®-99 Floor & Wall KH

A prepacked cementitious tile adhesive for installing ceramic, porcelain, and homogeneous tiles on floors and walls. Suitable for both interior and exterior applications as a thin or thick bed adhesive.

Overview

Specifications

Usage

• Wall and floor tile installation
• Ceramic, porcelain, and absorbing tiles
• Homogeneous tiles
• Interior and exterior use (mix with Sika® Latex for enhanced exterior adhesion)
• Thin bed or thick bed adhesive applications

Advantages

• Consistent quality and better workability
• Tile adjustable up to 20 minutes after application
• Good adhesion to concrete, cementitious mortar, stone, and bricks
• No pre-soaking of tiles required
• Compatible with Sika® Latex for increased performance
• Saves time and material cost

Packaging

• 20 kg / bag

Colour

• Grey powder (mixed to paste)

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Coverage: ~5.6–6.4 m² per 20 kg bag (based on 2 mm mortar thickness)
• Dependent on substrate profile, tile size, joint width, and application technique
• For tiles larger than 30×30 cm, buttering the back of the tile is recommended

Application Steps

• Substrate Preparation: Surface must be clean, sound, level, and free of oil or grease. Remove laitance and loose particles by sandblasting or high-pressure water jetting. Pre-wet absorbent substrates to saturated surface dry condition.
• Mixing: Add powder to ~4.0–4.6 L of clean water. Mix with a handheld or mechanical mixer for 3–5 minutes until a homogeneous, lump-free paste is achieved. Allow to stand 1–2 minutes, then re-mix for 1 minute before use.
• Application: Apply with a notched trowel onto the substrate and butter the back of the tile for better coverage. For tiles with deep grooves, ensure full coverage in the grooves. Press tiles firmly and tamp into position. Adjust within 20 minutes of application.
• Cleaning: Clean tools with water before material hardens. Hardened material can only be removed mechanically.

Sikadur®-31 CF Normal

A moisture-tolerant, thixotropic, structural 2-component epoxy adhesive and repair mortar for use at +10°C to +30°C. CE-marked per EN 1504-4 for structural bonding. No primer required.

Overview

Specifications

Usage

• Structural adhesive for concrete, natural stone, ceramics, fiber cement, mortar, bricks, masonry, steel, iron, aluminium, wood, polyester, epoxy, and glass
• Repair mortar for corners, edges, holes, and void filling
• Vertical and overhead applications
• Joint and crack filling, arris/edge repair

Advantages

• Easy to mix and apply
• Very good adhesion to most construction materials
• High initial and ultimate mechanical strength
• Thixotropic – non-sag on vertical and overhead surfaces
• Hardens without shrinkage
• No primer needed
• Different coloured components for mixing control
• Good abrasion and chemical resistance
• Impermeable to liquids and water vapour

Packaging

• 1.2 kg (A+B) pre-batched unit – box of 6 x 1.2 kg
• 6 kg (A+B) pre-batched unit – pallets of 480 kg (80 x 6 kg)

Colour

• Component A: White
• Component B: Dark grey
• Mixed: Concrete grey

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• ~1.9 kg/m² per mm of thickness

Application Steps

• Substrate Quality: Concrete and mortar must be older than 28 days. Surface must be clean, dry or mat damp (no standing water), and free from oil, grease, coatings, and loose particles. Steel must be de-rusted to Sa 2.5 standard.
• Substrate Preparation: Concrete/mortar/stone/bricks: remove laitance and contaminants to achieve an open-textured surface. Steel: blast clean and vacuum; avoid dew point conditions.
• Mixing: Mix components A+B for at least 3 minutes with a mixing spindle at max. 300 rpm until smooth and uniform grey. Pour into a clean container and stir for 1 more minute at low speed to minimise air entrapment. Mix only the quantity usable within pot life.
• Application: Apply directly to the prepared substrate. For vertical surfaces, product is non-sag up to 15 mm. Do not mix the next unit until the previous one is fully used. To extend workability at high temperatures, divide mixed adhesive into smaller portions or pre-chill components (not below +5°C).
• Cleaning: Clean all tools immediately after use with Sika® Colma Cleaner. Hardened material can only be removed mechanically.

Sikafloor®-161 HC

A 2-part, low viscosity multipurpose epoxy resin for priming and levelling concrete and cementitious substrates. Solvent-free with excellent bond strength and short waiting times. Suitable as a primer, bonding bridge, levelling mortar binder, and intermediate layer for Sikafloor®-263 SL HC and Sikafloor®-264 HC flooring systems.

Overview

Specifications

Usage

• Priming concrete substrates, cement screeds, and epoxy mortars
• Low to medium absorbent substrates
• Primer for Sikafloor®-263 SL HC and Sikafloor®-264 HC flooring systems
• Binder for levelling mortars and mortar screeds
• Intermediate layer underneath Sikafloor®-263 SL HC and Sikafloor®-264 HC

Advantages

• Low viscosity with good penetration into substrate
• Excellent bond strength (>1.5 N/mm²)
• Solvent free
• Easy application
• Short waiting times between coats
• Multi-purpose – primer, binder, bonding bridge, and screed
• LEED v4 EQ credit compliant – low-emitting materials

Packaging

• 20 kg set (Part A + Part B)
• 10 kg set (Part A + Part B)

Colour

• Part A (Resin): Brownish-transparent liquid
• Part B (Hardener): Transparent liquid

Product Details

Product Information

Technical Information

Pot Life

Curing & Ready for Use

Application

Application Information

Application Steps

• Substrate Requirements: Concrete must have min. compressive strength of 25 N/mm² and pull-off strength ≥1.5 N/mm². Surface must be clean, dry, and free from oil, grease, coatings, and contaminants. Moisture content <4% pbw.
• Substrate Preparation: Mechanically prepare using abrasive blast cleaning, planing, scarifying, or grinding to remove laitance. Grind high spots. Vacuum all dust and loose material. Fill cracks, blowholes, and voids with Sikafloor®, Sikadur®, or Sikagard® products.
• Primer Mixing: Mix Part A for ~30 seconds. Add Part B to Part A. Mix continuously for ~3 minutes at 300–400 rpm until uniform. Pour into a clean container and mix again. Scrape sides and bottom at least once during final mixing.
• Levelling Mortar Mixing: Mix Part A for ~30 seconds. Add Part B. While mixing, gradually add required filler/aggregates. Mix for a further 2 minutes until uniform. Pour into clean container and mix again.
• Standard Primer Application: Pour mixed product onto substrate. Spread evenly with short pile roller or squeegee. Back-roll in two directions at right angles with a fleece roller. Maintain a wet edge. If broadcasting, wait 15–30 minutes then broadcast quartz sand to excess. Vacuum loose sand after hardening.
• Bonding Bridge: Apply with brush, fleece roller, or squeegee. Back-roll in two directions. Apply second coat if required.
• Resin Screed: Pour wet-on-wet onto still-tacky primer. Spread and compact with trowel to required thickness between screed rails. Level with levelling beam. Finish with trowels or power floats.
• Cleaning: Clean all tools immediately with Thinner C. Hardened material can only be removed mechanically.

Sikafloor®-6 Chapdur Grey KH

A ready-to-use, dry shake cementitious floor hardener containing very hard, well-graded natural aggregates. Applied to freshly poured concrete to create a dense, high abrasion-resistant surface that reduces dust and improves impact resistance.

Overview

Specifications

Usage

• Superficial reinforcing of floor surfaces and slabs to increase abrasion resistance and reduce dust formation
• Warehouses and circulation lanes
• Mechanical engineering workshops
• Parking lots, service stations, and garages
• All floors subjected to severe mechanical wear

Advantages

• Intrinsic grey colouring
• High resistance to abrasion
• Reduces surface dust
• Improves resistance to impact, oils, and greases
• Easy application by hand sprinkling
• Eliminates the need for a monolithic screed
• Even finish when properly power-floated

Packaging

• 25 kg / bag

Colour

• Powder / Grey

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• 3–6 kg/m² depending on traffic load
• Normal traffic areas: 4 kg/m²
• Heavy traffic areas: 5–6 kg/m²

Application Steps

• Substrate Preparation: Once freshly poured concrete has reached plasticity (after bleeding, before setting begins), smooth and level the surface with a vibrating straight edge.
• Application: Sprinkle Sikafloor®-6 Chapdur Grey KH by hand over the smooth wet surface at 3–6 kg/m². Allow it to absorb moisture from the substrate until evenly moist, then consolidate and power float the surface.
• Smoothing: Pre-smooth with power float at low speed with metal blades at minimum inclination as the mixture becomes plastic. Carry out final smoothing at high speed once the surface is ready.
• Curing: Apply an approved curing system immediately after finishing to prevent rapid water loss and surface cracking.

SikaGrout®-214 KH

A pumpable, dual shrinkage-compensated, self-levelling, prebagged cementitious grout with extended working time. Suitable for machine foundations, structural repairs, and grouting works with clearances as low as 5 mm. Approved for compatibility with drinking water (PSB report 57S030976-SLE-2).

Overview

Specifications

Usage

• Machine foundations and base plate grouting
• Columns in precast construction
• Concrete anchors and anchor bolt grouting
• Bridge bearings
• Cavities, gaps, recesses, and rail beds
• Honeycombs (pre-packed grouting)
• Suitable for clearances as low as 5 mm

Advantages

• Easy to mix and apply with good flow characteristics
• Rapid strength development and high ultimate strengths
• Dual shrinkage compensation (gaseous expansion in plastic stage + crystalline expansion in hardened stage)
• Impact resistant, non-corrosive, non-toxic, and chloride free
• Extended working time and good pumping properties
• Approved for compatibility with drinking water

Packaging

• 25 kg / bag

Colour

• Grey powder

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Flowable: 1.84 kg per litre of mortar – 74 bags per m³
• Pourable: 1.90 kg per litre of mortar – 76 bags per m³
• For sections thicker than 50 mm, extend with graded 10 mm silt-free aggregates (max. 1:1 by weight)

Application Steps

• Mixing: Pour 70–80% of premeasured water into a clean container. Gradually add the full bag while continuously mixing. Add remaining water and mix for 2–3 minutes at ~500 rpm (slow speed drill and paddle). For large quantities, use a forced-action mixer. Do not use free-fall mixers.
• Application: After mixing, stir lightly with a spatula to release entrapped air, then pour immediately into prepared formwork. Maintain sufficient pressure head for uninterrupted flow. For large areas, maintain continuous flow and use heavy-duty diaphragm, screw feed, or piston pumps as needed.
• Specific Uses: Base plate grouting (pourable), formwork/honeycomb repair (flowable/pourable), anchor bolt grouting (stiff), large volume grouting >50 mm (extend with 10 mm aggregates, max 1:1 by weight).
• Curing: If formwork repair, leave formwork in place for at least 3 days. Upon removal, cure exposed surfaces immediately with Antisol®-E curing compound or approved equivalent.
• Cleaning: Clean all tools and equipment with water immediately after use. Hardened material can only be removed mechanically.

Sikalastic®-110

A water-based, one-part modified polyurethane/bituminous coating that forms a highly elastic, seamless, and crack-bridging waterproofing membrane. Easy to apply by roller, brush, or airless spray on horizontal, vertical, and overhead surfaces.

Overview

Specifications

Usage

• Waterproofing membrane for roofs, terraces, and balconies
• Below-grade waterproofing for basements and retaining walls
• Wet rooms, bathrooms, and podium decks
• Surfaces subject to crack movement and structural settlement
• Not suitable for water-retaining structures (RC tanks, swimming pools) or areas with permanent water immersion

Advantages

• High elasticity and crack-bridging capability
• Easy application by roller, brush, or airless spray – including vertical walls and ceilings
• Seamless, fully bonded waterproofing membrane
• One-part – no mixing required (except dilution for primer coat)
• Can be overlaid with cementitious screed after 48 hours

Packaging

• 20 kg / pail

Colour

• Black

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Standard system: ~1.5 kg/m² total (primer + 2 coats)
• Reinforced system: ~2.0 kg/m² total (primer + 3 coats + Reemat reinforcement)
• In hot/dry conditions (>40°C, ~50% r.h.), reduce to max. 0.5 kg/m² per coat or apply when temperature is below 35°C
• Figures are theoretical and exclude allowances for surface porosity, profile, and wastage

Application Steps

• Substrate Preparation: New concrete must be cured min. 28 days with pull-off strength ≥1.5 N/mm². Surface must be dry (<6% moisture), mechanically prepared to open texture, free from standing water, oil, grease, coatings, laitance, and loose material. Remove all existing membranes by industrial vacuuming. Repair blowholes and voids fully.
• Mixing: Mix Sikalastic®-110 manually or with a low-speed mixer until completely homogeneous before application.
• Standard Coating System: Dilute with 1 part clean water for primer coat (~0.2 kg/m²). Apply by short hair wool roller, brush, or airless spray. Allow to dry, then apply 2 coats of undiluted Sikalastic®-110 (~0.65 kg/m² each), ensuring each coat is completely dry before the next. Allow full system to cure 48 hours before screed overlay.
• Reinforced Coating System: Apply primer as above. Apply 1st coat (~0.8 kg/m²) and embed Sika® Reemat Premium-120 into the wet coating. Roll to remove bubbles and creases. Overlap edges min. 50 mm, borders min. 100 mm. Apply 2nd and 3rd coats (~0.5 kg/m² each). Allow 48 hours before screed overlay.
• Cleaning: Clean all tools with water immediately after use. Hardened/cured material can only be removed mechanically.

SikaTop®-107 Seal

A two-component polymer-modified cementitious waterproof mortar slurry for interior and exterior waterproofing and damp-proofing. Approved for potable water contact and suitable for wet rooms, swimming pools, and basement applications.

Overview

Specifications

Usage

• Interior and exterior waterproofing and damp-proofing of concrete, cementitious rendering, brickwork and blockwork
• Waterproofing for drinking water, wet rooms, and swimming pool systems
• Rigid waterproofing of basement walls (new construction and refurbishment)
• Pore and blowhole filling
• Sealing fine hairline cracks in concrete (not subject to movement)
• Levelling mortar for concrete repair works

Advantages

• Approved for potable water contact
• Protects against water penetration
• Easy to apply by brush or thin trowel
• Hand or spray applied
• No water required – pre-batched components
• Easy and fast mixing
• Very good adhesion
• Protects concrete against carbonation
• Non-corrosive to steel or iron

Packaging

• 25 kg/set
• Component A: 5 kg pail (liquid polymer)
• Component B: 20 kg bag (cement-based powder)

Colour

• Part A: White liquid
• Part B: Grey or white powder
• Mixed product: Cement grey

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• ~2.0 kg/m²/mm (guide only; excludes wastage, surface profile, and porosity allowances)
• Yield: ~12.5 L of mortar per set

Application Steps

• Mixing: Mechanically mix for 3 minutes using a forced action mixer or drill in a clean drum. Shake Part A before use. Pour approximately half of Part A into the mixing container, slowly add Part B while mixing, then add the remainder of Part A. Mix until a uniform, lump-free consistency is achieved.
• Surface Preparation: Pre-wet the surface slightly before application.
• As a Slurry: Apply by spray or stiff brush. Apply 1st coat in one direction; apply 2nd coat crosswise as soon as the 1st coat has hardened.
• As a Mortar: For trowel application (smooth finish), reduce Part A by 10% (~1A:4.5B). Apply 2nd coat as soon as 1st coat has hardened. For pore/blowhole filling, tightly trowel into the surface.

SikaWall®-126 Plaster Mix KH

A one-component, prepacked polymer-modified mortar combining cement with selected grades of sand and admixtures. Suitable for use as light brick plaster, red brick plaster, and red brick adhesive on various surfaces.

Overview

Specifications

Usage

• Plaster mortar on light brick and red brick surfaces
• Red brick adhesive
• For concrete surfaces, apply with bonding agent (Sika Latex® or SikaCim Latex®) while still wet
• Non-exposed applications only

Advantages

• Multifunctional: plaster, red brick adhesive, and all types of brick adhesive
• Excellent adhesion
• Easy to use – just add water
• Reduces cracking from plaster expansion and shrinkage
• Faster working process and time saving

Packaging

• 25 kg / bag

Colour

• Grey powder

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Red brick adhesive: ~0.78 m² per 25 kg bag (based on 10 mm thickness)
• Plaster: ~2.5 m² per 25 kg bag (based on 5 mm thickness)
• Actual consumption depends on substrate surface profile and layer thickness

Application Steps

• Substrate Preparation: Surface must be clean, sound, level, and free of oil or grease. Remove cement laitance, dust, and loosely adhering particles. Pre-wet absorbent substrates to saturated surface dry (SSD) condition.
• Mixing: Pour 3.2–3.5 L of water into mixing vessel, then slowly add SikaWall®-126 Plaster Mix and mix thoroughly for ~3 minutes using a slow speed mixer (300–600 rpm).
• As Brick Adhesive: Apply with scoop then fix the brick while product is still wet. Wait minimum 24 hours before plaster application.
• As Plaster: Apply with a flat trowel. Wait minimum 7 days before skim coat application. For best results, follow with SikaWall® Skim Coat.
• Cleaning: Clean all tools with water immediately after use. Hardened material can only be removed mechanically.

Sika® Igolflex® R

A solvent-free, flexible thick-film coating based on rubber bitumen emulsion with a pasty consistency. Ready-to-use with no mixing or heating required. Protects concrete surfaces against salty groundwater and mild soil acids.

Overview

Specifications

Usage

• Flexible external protective coating and vapour barrier for retaining walls
• Basement waterproofing
• Settlement tanks
• Protection against salty groundwater and mild soil acids

Advantages

• Suitable for dry and damp surfaces
• Easy to apply – ready-to-use, no mixing or heating
• Non-sag on vertical surfaces
• Good weather resistance and ageing properties
• Bridges shrinkage and hairline cracks
• Permanently plasto-elastic, even at low temperatures
• Odourless and fungus resistant
• Good resistance to mild soil acids and salts

Packaging

• 20 kg / pail

Colour

• Black

Product Details

Product Information

Technical Information

Application

Application Information

Consumption

• Priming coat: ~0.35 kg/m² (diluted 1:1 with water)
• Each subsequent coat: ~0.70 kg/m² (undiluted)
• Total system (3 coats + primer): ~2.45 kg/m²
• Optional fibreglass mat reinforcement: 75 g/m²

Application Steps

• Substrate Preparation: New concrete/screed should have a brushed or wood float finish, free from contamination. Repair all surface defects and remove protrusions greater than 3 mm. Existing surfaces must be dense and defect-free. Concrete must be mat-moist with no standing water. Brickwork should be flush pointed. Profile all horizontal/vertical intersections with a 25×25 mm mortar fillet.
• Mixing: No mechanical mixing required. Manually stir with a plastic spatula until smooth consistency is achieved.
• Application: Apply priming coat diluted 1:1 with clean water (~0.35 kg/m²). Allow 6–12 hours before applying 1st coat undiluted (~0.70 kg/m²). Optionally embed fibreglass mat (75 g/m²) into wet 1st coat. Apply 2nd and 3rd coats undiluted at ~0.70 kg/m² each, allowing 6–12 hours between coats.
• Cleaning: Clean all tools with water immediately after use. Hardened material can only be removed mechanically.

Sikagard®-703 GroutSeal

A ready-to-use, low viscosity silane/siloxane water repellent impregnation in aqueous phase. Deeply penetrates tile joints, concrete, and building surfaces to provide strong water resistance without changing the substrate appearance. Reduces dirt pick-up and inhibits fungal and algal growth. Water-based and environmentally friendly.

Overview

Specifications

Consumption

Usage

• Making tile joints and building surfaces water repellent
• Protecting against water ingress through hairline cracks in tile joints and concrete
• Exterior walls, roof tiles, brick, concrete, and mortar surfaces

Advantages

• Strong water repellent capability in aqueous phase
• Deeply penetrates tile joints and building surfaces
• Treatment is usually invisible – does not change substrate appearance
• Improves resistance to dirt pick-up
• Reduces fungal and algal growth
• Can be overcoated with suitable water or solvent-based polymer paints
• Ready to use – no mixing required
• Water-based and environmentally friendly

Packaging

• 500 ml bottle
• 1 L pail
• 5 L pail

Colour

• Whitish liquid (treatment is invisible after application)

Product Details

Product Information

Application

Application Information

Application Steps

• Substrate Preparation: Surface must be clean, dry, and free from dust, dirt, grease, oil, and loose particles. Ensure tile joints are sound and free from old sealant residues.
• Application: Apply Sikagard®-703 GroutSeal using a low-pressure spray gun, brush, or roller in a single layer from top to bottom. Take care not to let the product run or pool on the surface.
• Protection: Protect the treated surface from rain for at least 3 hours at +20°C after application.
• Overcoating: Can be overcoated with water or solvent-based polymer paints – contact the paint manufacturer for compatibility details. For Sikagard® polymer paint, wait at least 5 hours before applying.
• Cleaning: Clean all tools and equipment with water immediately after use. Hardened or cured material can only be removed mechanically.

Sikafloor® CureHard-24

A high-volume solids, one-part, clear sodium silicate-based liquid hardener and densifier for fresh or hardened concrete. Reduces dust emissions, increases abrasion resistance by 81.5%, and seals concrete surfaces. Odourless and easy to apply. CE marked per EN 1504-2.

Overview

Specifications

Usage

• Hardening and densifying concrete surfaces requiring light to moderate abrasion resistance
• Dust-proofing prefabricated concrete elements
• Horizontal old or new concrete surfaces
• Industrial, commercial, and public buildings – interior and exterior

Advantages

• Reduces dust emissions vs untreated concrete
• 81.5% increase in abrasion resistance vs untreated concrete
• Seals concrete surfaces
• Very good yellowing resistance
• One-part – ready to use
• Easy to apply by spray
• High gloss with regular cleaning
• Odourless
• LEED v4 MR Credit compliant – EPD available
• CE marked per EN 1504-2

Packaging

• 15 L container
• 200 L drum

Colour

• Clear

Product Details

Product Information

Technical Information

Curing & Ready for Use

Application

Application Information

Consumption

• 0.15–0.25 L/m² per coat (4–7 m²/L) on power-trowelled concrete
• A second coat is required on porous, rough-textured, or brush-finished surfaces

Application Steps

• Substrate – Fresh Concrete (≥7 days): Finish using power floating, manual floating, or tamping. Cure for at least 7 days with water spray, blankets, or plastic sheets.
• Substrate – Hardened/Old Concrete: Clean with high-pressure water cleaner. Allow to dry completely. Remove all dust, dirt, and loose material with brush or vacuum.
• Important – Remove Existing Treatments: Completely remove any curing agents, membrane-forming sealers, or asphalt before application.
• Application: Apply in a continuous film using a high-volume, low-pressure spray unit. Do not use sprayers previously used for silicones or release agents. Touch up any dry spots immediately.
• Scrubbing: Scrub material into the surface with a soft bristle broom or floor-scrubbing machine for minimum 30 minutes until the material begins to gel and becomes slippery.
• Reworking: Wet the surface slightly with water spray and rework for another 10–20 minutes.
• Removal of Excess: After ~20 minutes when material returns to a gel, rinse the floor and remove excess with a squeegee, wet vacuum, or mop. Dried residue leaves white stains removable only mechanically.
• Second Coat: Apply on porous or rough surfaces after the first coat is dry and tack-free.
• Before Subsequent Coating: After cure, abrade the surface mechanically (light to heavy shot blasting) before applying any subsequent coating system.
• Hot Weather (>+25°C): Store product in a cool place. Apply additional material to keep surface wet during scrubbing.
• Moisture Protection: Protect treated surface from moisture for at least 3 days after application to prevent efflorescence.

Aluminum Spirit Level 60cm 2-Vial — TOTAL TMT26036

Sturdy 60cm aluminum spirit level with 2 solid cylinder vials for horizontal and vertical readings. 1mm aluminum profile body with rubber end caps and 1mm/m accuracy for reliable results on construction and finishing work.

Specifications

What's in the Box

• 1× TOTAL Aluminum Spirit Level 60cm (TMT26036)

Materials & Care

• Body: Extruded aluminum frame with ABS end caps and rubber bumpers
• Wipe clean with a dry cloth; avoid solvents that may damage vials
• Store flat or hanging to preserve vial accuracy
• Do not drop — impact can shift vial calibration

Industrial Spirit Level 60cm 3-Vial V-Groove — TOTAL TMT26086

Industrial-grade 60cm spirit level with 3 solid vials for horizontal (180°), vertical (90°), and 45° readings. High-accuracy 0.5mm/m tolerance, 1.5mm aluminum frame with two precision-milled measuring surfaces, V-groove bottom for pipe work, and heavy-duty rubber end caps for shock absorption.

Specifications